Best Price

 

Best Price bench Dog 40 001 For Sale. Buy Now!.

Have to say it took a little bit of time to put together but nothing too hard or too vague. Mine didn't include hex wrenches but they were standard and I had them so no big deal. What is a bigger deal is the dust collection port.



I plan on doing dust collection via shop vac. Mine has a standard 2 1/2 inch hose which according to Bench Dog is supposed to fit their dust collection port. It does not. I took the port with me to The Home Depot, Lowes and Sears but could not find a 2 1/2 inch hose that would fit it. So much for standard. I called Bench Dog support and it seems they have been acquired by Rockler. Rockler has revised the port and while I had the newer one some were made with a smaller ID. Seems like someone forgot to tell mfg that the wall thickness was supposed to go on the outside and not the inside of the opening. They sent me the revised one. That took two weeks because the first time the order didn't go out. After waiting the normal time to call, they said oh, gee it didn't ship so will try again. They included a free set of hold downs as compensation and this time it did ship. But it still doesn't fit any hose I could find. The ID is exactly 2 1/4 inches. That is what a standard 2 1/2 inch hose fitting is supposed to be apparently. However it is actually about 2 5/16 with most being fitted into a 2 3/8 coupling. So if the Rockler people would have made this at least 2 5/16 or 2 3/8 things would be fine. I ended up buying a 1 1/4 to 2 1/2 adapter, cutting the 1 1/4 part off and duct taping the rest to the dust port. Works fine. I suppose I could have sanded my hose end down some as well.



The table works fine. Nice and solid, etc. Would have been nice if they would have included an external switch as it is obviously unsafe to open the door to turn off the router. Using a Triton router and had to drill holes to mount. Bench Dog includes a paper template with the proper hole spacing. These were accurate so that was a non-event to do.



I would give the table a 5 if this review was just confined to that part. Having to fool with the dust port because they can't check the fit on a hose by buying and trying a few before spec'ing and the lack of an external switch makes this just average for the cost. Even Bosch on a less expensive table includes a switch and presumably a dust port that fits a shop vac hose.





So far this router table has worked well for me. They included many parts and some extras and warned the purchaser about this in the instructions. Unfortunately, they changed some of the parts (fence, dust collection connector) from the original that the instructions were written for. They also did not include the tools that they said were enclosed ( Allen wrenches and open end wrenches). That being said, most of us have the tools and can figure out the change in parts and dirctions. What grinds me a bit is that they include a very friendly slip that says to contact them if anything is wrong. I told them of the missing parts and directions and parts changes via the email address provided and had no response. I like the router table so far - not so sure what would happen if I have a problem with it considering their lack of responsiveness.





I recently purchased this table from amazon and the shipping was quick and it arrived timely and in great shape. There are plenty of good reviews here to read so I won't go into a lot of detail about the table itself. It is well built and is a very good table for the $.



I will just share my experience with the table since it arrived. First, the instructions are not accurate. There are several steps in which the picture does not match the parts. Particularly, the bit guard in the box does not match the one listed in the manual and the subfence construction is completely different. Its like they updated or changed parts on this model and didn't bother changing the instructions. Nothing wrong with the subfence itself, it just doesn't match the book and makes it unclear how to put it together.



Most importantly, there were a couple parts missing from the box I received. The hex wrenches that are supposedly supplied were not included; no big deal since I had plenty. The dust port was missing as well as the whole set of bolts used to attach the router plate to the router. So I emailed benchdog from their website requesting the missing parts and also included some suggestions for the manual. Its been a week now and I have yet to hear anything from them at all.



All in all, this is a great table if you don't have to deal with benchdog and you actually get all the parts that are supposed to be included. This may be an isolated incident for all I know but I just wanted to share my experience for what it's worth.





This is for sure one of the best small router table packages on the market. The cabinet is heavy constructed laminated lumber and the top appears to be phenolic. I have it coupled to a PC 7518 with Bench Dog's nickel plated adjustable insert and there is no deflection. The fence works very well and is easily adjusting - you can couple it to a dust collection system fairly easily. Rubber feet secure it well enough so that it doesn't move with large stock. The edge mounted track works well with miter gauges. No complaints here. Amazon has very competitive prices on Bench Dog gear.





I read all the 3 star and below reviews here and I think they aren't to be taken as accurate or fair. (P.S. It is not particle board, it is finished plywood, actually nicer than I expected). This is a $200 router table okay. Let's say it again, a $200 router table. Have you seen $700 - $1000 router tables, like the Jessem? You should. This is not that table and can't be compared. It can't handle the match in features, size or materials. However, taking that all into account it is a great deal and if you are just getting into routing this is probably the best low cost router table you could get. Kreg, Freud, Bosch, Pinnacle... none match this little gem. It has a great fence and even comes with a jointing feature that works well with a good bit. It is solid, has very good dust management. The top is nice and though you probably shouldn't profile an 8 foot long board on it, you can do a lot - you can even flip the fence for a larger working area and wider pieces (it's in the manual). Sure, putting it together had shades of Christmas Eve - the instructions weren't perfect and I admit it, I put the feet on the wrong side of the bottom panel due to a lousy picture and cursed a little while I switched them.



If you are looking for a router for this, the Porter Cable 690 fits very well. I take the motor down to prevent any sag in the plate. Why push it? It only takes a minute. Again, if I had a $1000 table with a steel or phenolic plate and a lift, then okay, but I don't.



When all was said and done I have used this table and it is great. Everything I make with it turns out very well. No, I am not making raised panel doors. This isn't the router for that, but if you have a home shop and wanted a router table, get this. Maybe you will go on and buy something else or make your own. Great, but while you use this table you will make nice things all while learning what you may or may not need in your ultimate dream table.





There isn't much I can say that the manufacturer of this fine product has not already described, so I will limit this review to my impressions of it's design. I was searching for a quality router table that would accommodate my router without modification, and was capable of handling fairly large work pieces, particularly raised panels for cabinet doors. This table accomplished both wonderfully. The construction of the table is first-rate, utilizing birch plywood for the base and sides. The top employs a thick laminate as opposed to a melamine finish, as used in some lower quality tables. The router is supported on a large sturdy insert, and a metal frame with adjustable gib screws to level the plate to the table. The table comes unassembled, in a well-packed box. The assembly instructions are clear and easy to follow, and it took about 1 hour to put the table together and make all the necessary adjustments. All components that comprise this table are of excellent quality. Overall, this is a fine addition to my shop, and I would not hesitate to recommend this product.





this table went together in about 1 hour. all parts where finished well. i had to drill the holes for my trition router but with their template it when well. just wish they would have had a metal plate. but all in all a good table for the money.





Very happy with this purchase. Reasearched several other brands and settled on the Bench Dog. Have used it for multiple jobs and have been very satisfied. Also purchased the switch and mounted in on the right corner below the table. It makes it it easier for operating the router. I have a Porter Cable 6902 Router, it bolts right on!





I'm no pro, just a handy homeowner. Needed to make a window seat for the Mrs., and needed to do some routing for joinery, trim, and the like. Had the router, (a Freud model) but knew I needed a table. Looked at the usual suspects at Sears, Home Depot, Lowes. All looked way too flimsy, even to my amateur's eye. Saw this table on Amazon, read the mostly glowing reviews, and decided to pony up the dough after assuring my wife that I really needed this to do the job right. Amazon had a deal for the table and a pair of featherboards at a discount, so I ordered both.



Table came within 4 days, even with free shipping. Featherboards were backordered and actually arrived the day I finished the job! The table's packaging was adequate, all the parts were there (with a few extra screws and such) and in pristine condition, the assembly instructions were excellent -- clearly written by someone for whom English is their primary language! Assembly took me exactly 2hrs and 10 minutes -- not counting the drilling I had to do to fit my router to the plate. That was a bit scary, since two of the holes I needed fell very close to some of the pre-drilled ones. But, taking my time, I got it right, leveled and ready to go.



I built a sub-cabinet from an old (heavy) printer stand, then attached locking casters so that the router table top would be on the same plane as my table saw. I can't tell you how useful THAT was! The Bench Dog table is substantial, very good quality materials and engineering. Again, as others have noted, despite Amazon's claim, this table does NOT come with a miter gauge. Squaring the fence is easy, but I am a bit disappointed that both long edges of the top are not square -- the "rear" is slightly rounded, which can be a problem when squaring the fence to that side.



Overall, though, this is a terrific American-made product. I also purchased a Bench Dog power switch -- expensive as switches go, but rock solid and easy to mount (as I did on the right side under the table top). If you want a solid, well-designed, easy to use and functional portable router table, the Bench Dog ProTop is hard to beat.





I bought one of these used from a buddy. I was surprised at how beefy the construction is. It is made from 3/4" thick baltic birch plywood and is quite heavy. (on the order of 40 lbs.) Everything has been well thought out, and everything is milled with precision.



There are only two minor things that I wasn't happy about:



1) It didn't include a feather board. c'mon guys. What does it cost to include that, Fifty cents?



2) Sometimes the whole cabinet reverberates loudly.



I was deciding between this one and the Kreg. This one has a smaller footprint and is made out of nice-looking wood. The Kreg doesn't have the enclosed cabinet, so it is not going to reverberate like this one does, and it includes at least one featherboard. (but costs $10-20 more)



If I had bought the Kreg, it would've been just big enough to NOT fit on the shelf under my workbench, so no regrets.

Images ScreenShot

About Bench Dog 40-001 ProTop Contractor Benchtop Router Table detail

• Amazon Sales Rank: #2748 in Home Improvement


• Color: Brown/Orange


• Brand: Bench Dog


• Model: 40-001


• Number of items: 1

Features

• Ample 16-by-22-inch router table with plastic laminate top


• Clear acrylic insert accepts most routers; melamine cabinet


• Extruded aluminum fence with T-slots


• All necessary hardware and assembly instructions included


• Limited 2-year warranty

Read more Bench Dog 40-001 ProTop Contractor Benchtop Router Table

Related Product

Source From Best Price Bench Dog 40 001 For Sale Best Buy Bench Dog 40 001 Low Price Buy Cheap amp Review

Have a COOL !

Cheers

 

 

Best Price Porter Cable FR350MAG For Sale. Buy Now!.

Have used this tool on one small job so far (shot about 1250 nails, two different sizes) and it is as reliable as advertised. Does not wear you out when used all day. I have used a Bostitch nailer previously, and the 350MAG is clearly the better nailer. I am a DIYer, and not a pro. This nailer should last me for a lifetime.


Love this tool .....Makes making walls a snap
Rugged

Lighter than standard unit very helpful for bigger projects!

5+ Stars! JMHO


The framing crew likes this gun. It's light weight. It shoots the fat common nails that engineers are starting to specify, unlike the FR350A. Single fire is now an adjustment on the trigger so no accessory is needed. Depth adjustment requires an allen wrench. You will need a real air compressor that produces at least 9 cfm at 100 psi to keep up with bounce nailing subfloor and sheathing.


This is what I expect of a 110 year old company such as Porter-Cable. I can not wait to put up our new fence.


I have gone through over ,5000 nails and my nailer has performed flawlees. In both 2-3/8" and 3-1/2" long full head nails. I dropped my nailer a few times and it still continues to perform the way it did on the first day. The light weight was definitely a plus, since I used it to secure over 1800 square feet of 1" rough sawn boards on a garage roof that I was building. I also used the nailer in securing the framing made out of 2x6 lumber.

Regards John


I have minimal expertise in this area, so keep this in mind as you read my point of view. However, I know good and bad product concepts and customer relations. <p>I bought and returned this as it leaked air from the head. It happens. That is not a reason to not buy this. But, no case after many have complained... It has been out for a couple of years.(read reviews) shame on you, PC. A $10 plastic case. Please , how cheap and stupid, PC. The problem is; if you are a framer you may want the light weight, but if you are a home user it may be better to go with the 350 regular. I did after returning the MAG 350. It is not that much more weight, a pound at most. A few reasons. 1)It is $40 less 2) comes with a case 3) Has the dial on the trigger to change from bump fire to sequential (which is good for the less experienced/home user...we be dangerous...some at least...) 4) I have the PC brad and finish guns and called PC almost 2 months ago to get the free trigger to allow bump/continuous nailing...backordered. I may never use the seqential, however, I would like to have this. Why not include this in the box, or, at least have it as a dial on the trigger. 5) It can take a 2" - 3 1/2 nail, the Mag takes a 2 3/8 min -3 /1/2. Better yet, buy a DeWalt D51844 Full Round Head Framing Nailer, Magnesium, 7 .5 lbs. <br>for around the same $ , 20 less actually (239- here, at amazon ..the best place to buy tools or anything for that matter ) if you want a lighter tool. I believe it comes with the extra trigger to change from bump to seqential, not a dial, though. But, I do not think it has a case. So, another bunch of clowns. Oh, well. <br>Is it as good? I would not know. I do know that PC is a less than good company to buy from. So, because PC was not and is not responsive I did not hesitate to order a Bosh Router from Amazon last week. Maybe , I hope, Bosch is more customer responsive. I just bought the Bosch 4000 table saw also, and it is nice.


I purchased this nailer to use primarily in building and repairing three board fence. For this it does an excellent job in the field. It is also precise enough to use in more delicate jobs. I used it to build three benches from salvaged 1" barn floors. It worked like a high-powered finish nailer. Overall a solid tool that has paid for itself with time savings.


Used this nailer for 1-1/2 years on home and cottage projects -decks, docks, siding, fencing etc. It is a great nailer never jams and is light to use. My only issue is that the 3-1/2" .131" nails available have about as much holding power as a wet noddle. Has anyone found better framing nails? When I hand nailed I used twist nails that have great holding power.


This unit is super. It loads easily, it shoots solidly and has yet to jam. In fact none of my PC nailers have ever jammed, whereas my Bostitch units did so repeatedly. <p>PC has lived up to it's name with this one. I sure wish that they would provide a case for it though!


I gave this nailer four stars because it doesn't come with a case, and I don't think Porter Cable even makes an aftermarket case. Also, the depth of drive adjustment is not the greatest. That being said, this is a fine framing nailer and is lighter then most. I really like the way nails are loaded and advanced(it loads similar to the senco guns). Compared to the Hitachi NR83, it has similar power, it is better balanced, and has way fewer jams because of the way it advances the nail strips. <p>I think Porter Cable nailers are under-rated in general. The Hitachi's are extremely popular with framers here on the west coast, and they are good nailers. However, for less money, the magnesium PC framer is hard to beat. It is a hard working tool and I have had no problems with it so far. I have owned it about one year and it has been used for framing, sheathing, and decking. The only thing I have not liked is that it was difficult to adjust the depth of drive to allow for flush nailing decking boards with 8d nails. For framing applications, it has been basically maintenance free and pretty much flawless. I just keep it well oiled and work it hard.

Images ScreenShot

About Porter-Cable FR350MAG Round Head 2 3/8-Inch to 3-1/2-Inch Round Head Framing Nailer with Magnesium Housing detail

• Amazon Sales Rank: #32285 in Home Improvement
• Brand: Porter-Cable
• Model: FR350MAG

Features

• Round head framing nailer uses 2-3/8 inch to 3-1/2 inch nails
• Selectable trigger -- restrictive or contact actuation mode
• 70-120 PSI operating pressure
• Measures 19-1/2 inches long and 14 inches tall; weighs 7.4 pounds
• Includes 3/8-inch NPT air inlet with 1/4-inch air fitting with dust cover, oil, and wrench

Read more Porter-Cable FR350MAG Round Head 2 3/8-Inch to 3-1/2-Inch Round Head Framing Nailer with Magnesium Housing

Related Product

Source From Best Price Porter Cable FR350MAG For Sale Best Buy Porter Cable FR350MAG Low Price Buy Cheap amp Review
Have a Nice Days!
Cheers

 

 

Best Price Porter Cable 360VS For Sale. Buy Now!.

This sander literally is a horse!!!!! Big,heavy,and powerful. So powerful I dial the variable speed back to control it. Very hard to control at the fastest speed.Dust collection is good but not superb like the makita 9910 3x18 I also own.Heavy weight increases stock removal. Works great for leveling tables.


As a reviewer I have to be honest about this sander. It is a real nice powerful sander and I find it on a par with my old Black and Decker as far as noise goes. The only complaint I have and this was a big one for me is that when I tried to get in close to a wall a bulge on the side kept the sander out about three quarters of an inch. It's a good thing I didn't give the old Black and Decker away because I had to put it back to work to get in close. If your not doing floors then you would be purchasing a fine machine.


I've had this sander for four years, and use it extensively. It has a good design, and is well built. It is light enough to be held with one hand for scribing, and stable enough for flat sanding.
On the down side - the dust bag is a joke. It never worked right, and tore and fell off after a month. It also gets hot after a few minutes of hard, constant use. But I've also had no down time with it. It handles well, and made to last. If you do a lot of flat sanding, I'd recommend a heavier sander. For all around service though, it's a keeper.


The dust collection doesn't work. Take the side cover off and see for yuorself, Porter Cable blocked the rear dust collection port with a strip of metal. They put the port onthe top which is useless. Remove the strip and the fanand use a vacuum or buy a different sander.


If you are looking for a professional belt sander, this is the one to own. Porter-Cable invented the belt sander, and this shows why they are still the industry leader. The 12 amp motor does not bog down. The swivel feature on the dust bag will keep it out of your way, and it's quiet, unlike many competitive models. Simply put, it does it's job, and does it well.

Images ScreenShot

About Porter-Cable 360VS 12 Amp 3-Inch by 24-Inch Variable Speed Belt Sander detail

• Amazon Sales Rank: #6667 in Home Improvement
• Brand: Porter-Cable
• Model: 360VS
• Dimensions: 10.25" h x 10.00" w x 17.75" l, 14.50 pounds

Features

• 3 x 24 inch variable-speed belt sander with powerful 12 Amp motor that spins the belt at 1,000-1,500 SFPM
• Quick-release belt changing system
• Equipped with a large capacity dust bag
• Measures 7 x 8 x 20 inches (WxHxL) and weighs 14.5 pounds
• Includes 100G ceramic aluminum oxide belt, dust bag assembly, manual

Read more Porter-Cable 360VS 12 Amp 3-Inch by 24-Inch Variable Speed Belt Sander

Related Product

Source From Best Price Porter Cable 360VS For Sale Best Buy Porter Cable 360VS Low Price Buy Cheap amp Review
Bye Bye
Cheers and Care

 

 

Best Price Porter Cable 895PK. Free Shipping. Buy Now!.

i love this router. by far has enough power for any job. the only thing i don't like is that it comes with one wrench for bit changing. It uses an awkward button to hold the arbor still which is great in idea but impractical once you have used the router and accumulated any dust on the unit. It has a slow start which is great. i work as a cabinet installer and recommend this router to all of my apprentices. i also recommend the bosch 1-1/2 horse power trim router for tighter quarters.


This is my 5th Porter Cable router.
Finally they have a spindle lock... I think.
Thank God they still have 2 lock nuts on the collets, because the spindle lock pin broke off after a bit was over tightened some and seized in the new collet.
Maybe thats my fault but I wished the spindle pin was beefier, because I won't be alone with this issue.
I am used to the 2 wrench system, so it's not a BIG deal here, and the tool is perfect with out it. Would be 5 stars except for the spindle lock breaking.
Still it's a great kit, including the guide and above table adjuster, which have been used and accepted as designed.
The motor drove a large panel bit thru MDF door panels, at 10800 rpm, with no issue or groan at all.
Great kit.


I am a retired school shop teacher and had three Porter-cable 690 1 ¾ hp fixed speed routers in my shop. Each was used extensively in a router table by students. These three routers held up for over 20 years and where still in very good shape when I retired. I needed a new router for my home shop so I thought that the 890 2 ¼ hp would be a step up from the 690 and it had a better adjusting mechanism, which was advertised as good for use in a router table.

I would not recommend getting an 890 series router for use in a router table. I have had two new 890 routers and one rebuilt one burn up on me doing exactly the same operations that my students and I had done for years with the 690. The first one burnt up while using a raised panel bit on MDF; hard stuff but nothing that had not been done before with the 690. I needed to get the job done so I ran out a bought another one thinking maybe I just got a lemon or I had overloaded it by feeding too fast. I finished the job but took three passes just to be careful. Later I took the other one in and got it repaired one month out of warrantee, but they covered it. I now had two routers on hand; ok that might be handy.

I used them for various task with no problems even routing over 300 foot of 1/2 by 3/8 fluting in MDF in one afternoon. Then months later a friend needed help with a project. I used the new router to make 3/8 by 1/2 inch grooves in 3 foot long pieces of cherry. I got through the first piece and halfway through the second and the router started to smoke then lost power. I setup the rebuilt router and finished the cut then reduced the cut depth to 1/4 to make multiple passes for the remaining pieces but it burnt up before the job was done. The bit was a new carbide bit and I even went extra slow on the second router.

I think the problem is the electronic speed control; it tries to maintain the same speed no matter what the load. The operator can not listen to the motor to determine if he should change his feed rate and before you know it the motor has over heated. I would take a 690 router over an 890 router any day.



this is by far the best router on the market for the price. PC stood up with their excellent engineering. lots of power in this router. the micro fine adjustment from above in the router table is just super. the edge guid works really well with this router combo as well. all in all its a very good router and i would recommend this router to anyone.


I bought the 895 when they first came out several years ago. In that time I've used it quite a bit and the following are my impressions.

The bottom line is it's not worth the price they're asking these days ($280).

The positives; 1)soft start - no jerking on start-up, 2) high/low switch - you can sit it down on it's top and it will turn off leaving you free to keep both hands on the router, 3) strong motor - I have rarely been able to bog the motor down, 4) above the table height adjustment - (this is only a minor positive) - given the high cost of aftermarket router lifts this gets a + mark for it's crude yet convenient adjustment.

The negatives; 1) the plunge base is JUNK - the old style base (pictured above but I understand they've redesigned it now) sticks all the time, loses it's depth setting repeatedly, and the sub-base isn't flat, 2) above the table height ajustment - I know I listed this as a positive but it's also a negative - it's very crude and the bit moves when you lock in the setting, 3) the plunge base is JUNK, 4) both bases are cheaply made (however the motor seems solid), 5) did I mention the plunge base s JUNK?

I think this is a good table router if you have an aftermarket router lift, otherwise I would recommend going with another brand for an all purpose router.


I purchased the 895PK approximately 20 months ago through Amazon. The above the table bit changing and height adjustment along with the Porter Cable name were the main factors in the purchase. I mounted it in my homemade router table hanging off the right end of my table saw in a Rousseau plate.

Initially it was everything I hoped for. Then the following occurred: 1) the motor recall (just took awhile); 2) the spindle lock broke (repaired but still doesn't work - now using a bent wrench with the standard wrench); 3) Height adjustment rack broke in half and the small screws that hold it to the motor stripped out (bought new screws at the hardware store and holding rack pieces in place - waiting for it to break completely); 4) Adjustment Clamp came apart, affecting above table adjustment (tightened and pressed adjustment bit back into clamp assembly).

The motor has been great. The above table height adjustment works. I've had no problem with the plunge router, but have used it very little. The service center is about an hour away. I find myself wondering if I should have purchased a quality router lift along with the motor.


came out of the top within one hour's use. They call it a 2-1/4 HP router, but it doesn't have the guts of the classic PC 1-3/4. Between going to buy it, and driving back to return it, I spent more time on the road than the router lasted. I'll rate this a one, because I can't rate it negative 4.


I would like to say that I'm related to the Porter side of the company but I'm not. However, there are some things this company does well and making routers is one of them. I purchased this kit from Amazon a couple of years ago after doing a bit of research. It has not disappointed me. The soft start is a nice feature so as to not make it jerk in your hand when starting up. It also runs quieter than my old router.

Both bases work very well. I mostly use the fixed base in a Bench Dog router table to make cabinet doors and such. The plunge base works smoothly too when whatever I'm doing calls for it. I have not experienced the plunge base giving me any problems as some of the other reviewers have stated.

The motor is plenty powerful. It has never bogged down on me even when I've run maple or oak through it.

There are only a couple of things that I have had any difficulty with. When I'm using the fixed base in the router table, saw dust can collect between the motor unit and the base making it sometimes difficult to remove the motor unit from the base. Dust collection needs to be running at 100% to keep this from becoming an issue.

The other minor complaint I have is that the spindle lock doen't fully engage unless the motor unit is forced into position. It can sometimes be difficult to release the spindle lock from that position too.

These two "issues" are not severe enough for me to rate it 4 stars. I'd give it 4.8 if that was an option.


I had and still have a Mikita 1 1/4 router but wanted to upgrade. Saw this kit since I wanted both a fixed and plung router. I use the fixed base on my P/C router table. I have been milling my own wood trim for my house, and have no problem with it bogging down on me. I have been using white ash and the veriable speed is very helpful. So far the only thing that I have had a problem with is I have to replace the switch on my router table, but I bought that 7yrs ago, and it just went out on me last week.


I returned this due to many additive problems. Fortunately, Amazon refunded me because PC customer service just sent canned "Thank you - won't help you" messages. PC quality is sinking.
1) cheap plastic parts on bases - plunge base pointer broke on first use. You can't read the scale anyway because of how they positioned the knob.
2) cheap metal and screws. Two screws about 1/8" long w/maybe 3 threads hold the height adjustment rack to the machine body. These fall out and quickly strip both themselves and the body when you try to re-attach the rack - something I had to do with each use in a router table. What are they thinking? These tiny screws have to support the entire weight of the router when mounted on a table and the clamp is loosened to perform height adjustments.
3) Poorly machined base plate holes. Base barely fits standard jigs for PC routers (no problem with PC 690) because they are machined enough out of alignment to require a forced fit. You could tell this would lead to more thread stripping in no time.
4) Plunge mechanism was very stiff and almost useless. Did not improve with use.
5) For me - 4 hour one-way drive to service recall - no other way offered to accommodate.

The motor seemed decent and I tried to overlook the above until the metal began stripping in less than two months of use. I think PC is economizing on bases and cheaper manufacturing processes. By the way, this is the first tool I've returned in 20 years and own many other PC tools without complaint. Maybe I got a bad apple, but others here have similar experience with this model.

Images ScreenShot

About Porter-Cable 895PK 12 Amp 2-1/4-Horsepower Fixed- and Plunge-Base Base detail

• Amazon Sales Rank: #2113 in Home Improvement
• Brand: Porter-Cable
• Model: 895PK
• Number of items: 1

Features

• Variable speed plunge router kit offers extremely accessible height adjustment controls
• Ultra-powerful, low-noise 2-1/4 HP motor with superior electronic feedback (10,000 - 23,000 RPM)
• Made of durable, die-cast aluminum
• Weighs 22.0 pounds
• Comes with CD-ROM, carrying case, transparent sub-base, 1/4-inch and 1/2-inch self-releasing collets, one wrench, dust collection insert, and table-top height adjustment handle with measurement ring.

Read more Porter-Cable 895PK 12 Amp 2-1/4-Horsepower Fixed- and Plunge-Base Base

Related Product

Source From Best Price Porter Cable 895PK Router For Sale Best Buy Porter Cable 895PK Router Low Price Buy Cheap amp Review
I would be grateful if you would give me the Interview
Cheers !.